cisco
交换机上的链路聚合
一、2层 ethernet channel
（interface)#channel-group number mode {on | auto [no-silent]|desirable [no-silent]}
on 使用EthernetChannel 但不发送pagp分组
off 禁用EthernetChannel
desirable 交换机主动要求形成一个EthernetChannel 发送pagp分组
往往可能EthernetChannel的一端（一台服务器或者是网络分析仪)#没有产生pagp分组或者说是保持
使用non－silent关键字则要求在激活EthernetChannel之前现进行pagp协商、
Catalyst 2900 3500xl 平台上没有pagp 只有 on off不进行协商
ios （global)# port-channel load-balance method
――源地址 src-ip
――目的地址 dst－ip
――源和目的 src－dst－ip
――源mac地址 src－mac
――目的mac地址 dst－mac
――源和目的mac src－dst－mac
――源端口号 src－port
――目的端口号 dst-port
――源和目的端口号 src-dst-port
example
|
(global)# interface fastethernet 4/1
(interface)#channel-group 100 mode desirable non-silent (global)# interface fastethernet 4/2 (interface)#channel-group 100 mode desirable non-silent (global)# interface fastethernet 5/1 (interface)#channel-group 100 mode desirable non-silent (global)# interface fastethernet 5/2 (interface)#channel-group 100 mode desirable non-silent (global)#port-channel load-balance src-dst-ip show etherchannel [channel-group] load-balance |
绑定到一起的端口必须具有相同的属性如：速度双工模式 vlan 干路模式 允许的vlan范围
3层 etherchannel
1创建逻辑端口通道
interface port－channel number
2.配置端口通道上的协议信息
ip address address netmask
3.把物理3层接口分配给通道
interface type mod/port
选择的端口必须是一个3层接口 no switchport
4.删除任何协议地址
no ip address
5.把接口分配给通道组
channel-group number mode {auto |dusirable |on}
6.核实接口已经启用
no shutdown
7核实通道
show ethernetchannel number port-channel
show interface type number etherchannel
show ethernetchannel summary
example
分布层交换机上
|
(config)#interface channel-group 1
(config-if)#ip address 192.168.1.1 255.255.255.0 (config-if)#interface gigabitethernet 1/1 (config-if)#no switchport (config-if)#no ip address (config-if)#channel-group 1 mod on (config-if)#no shutdown (config-)#interface gigabitethernet 1/2 (config-if)#no switchport (config-if)#no ip address (config-if)#channel-group 1 mode on (config-if)#end copy run start |
接入层交换机（3500xl)#
我的试验3750配置实例 CastLyst
3750G
|
Switch#config t
Switch(config)#int gigabitEthernet 1/0/23 Switch(config-if)#channel-group 10 mode ? active Enable LACP unconditionally auto Enable PAgP only if a PAgP device is detected desirable Enable PAgP unconditionally on Enable Etherchannel only passive Enable LACP only if a LACP device is detected Switch(config-if)#channel-group 10 mode desirable non-silent Switch(config)#int gigabitEthernet 1/0/24 Switch(config-if)#channel-group 10 mode desirable non-silent Switch(config)#port-channel ? load-balance Load Balancing method Switch(config)#port-channel load-balance ? dst-ip Dst IP Addr dst-mac Dst Mac Addr src-dst-ip Src XOR Dst IP Addr src-dst-mac Src XOR Dst Mac Addr src-ip Src IP Addr src-mac Src Mac Addr Switch(config)#port-channel load-balance src-dst-ip Switch#write Switch#show interfaces gigabitEthernet 1/0/23 etherchannel Port state = Up Sngl-port-Bndl Mstr Not-in-Bndl Channel group = 10 Mode = Desirable-NonSl Gcchange = 0 Port-channel = null GC = 0x Port index = 0 Load = 0x00 Protocol = PAgP Flags: S - Device is sending Slow hello. C - Device is in Consistent state. A - Device is in Auto mode. P - Device learns on physical port. d - PAgP is down. Timers: H - Hello timer is running. Q - Quit timer is running. S - Switching timer is running. I - Interface timer is running. Local @R_280_4045@ion: Hello Partner PAgP Learning Group Port Flags State Timers Interval Count Priority Method Ifindex Gi1/0/23 U4/S4 H 30s 0 128 Any 10123 Age of the port in the current state: 00d:00h: |
版权声明：本文内容由互联网用户自发贡献，该文观点与技术仅代表作者本人。本站仅提供信息存储空间服务，不拥有所有权，不承担相关法律责任。如发现本站有涉嫌侵权/违法违规的内容， 请发送邮件至 [email protected] 举报，一经查实，本站将立刻删除。
