一、使用命令设置ubuntu的ip地址
1.修改配置文件blacklist.conf禁用IPV6:sudo vi /etc/modprobe.d/blacklist.conf2.在文档最后添加 blacklist ipv6,然后查看修改结果:cat /etc/modprobe.d/blacklist.conf3.设置IP(设置网卡eth0的IP地址和子网掩码)sudo ifconfig eth0 192.168.2.1 netmask 255.255.255.04.设置网关sudo route add default gw 192.168.2.2545.设置DNS 修改/etc/resolv.conf,在其中加入nameserver DNS的地址1 和 nameserver DNS的地址2 完成。6.重启网络服务(若不行,请重启ubuntu:sudo reboot):sudo /etc/init.d/networking restart7.查看当前IP:ifconfig二、直接修改系统配置文件ubuntu的网络配置文件是:/etc/network/interfaces打开后里面可设置DHCP或手动设置静态ip。前面auto eth0,让网卡开机自动挂载。1. 以DHCP方式配置网卡编辑文件/etc/network/interfaces:sudo vi /etc/network/interfaces并用下面的行来替换有关eth0的行:# The primary network interface – use DHCP to find our addressauto eth0iface eth0 inet dhcp用下面的命令使网络设置生效:sudo /etc/init.d/networking restart也可以在命令行下直接输入下面的命令来获取地址sudo dhclient eth02. 为网卡配置静态IP地址编辑文件/etc/network/interfaces:sudo vi /etc/network/interfaces并用下面的行来替换有关eth0的行:# The primary network interfaceauto eth0iface eth0 inet staticaddress 192.168.2.1gateway 192.168.2.254netmask 255.255.255.0#network 192.168.2.0#broadcast 192.168.2.255将上面的ip地址等信息换成你自己就可以了.用下面的命令使网络设置生效:sudo /etc/init.d/networking restart3. 设定第二个IP地址(虚拟IP地址)编辑文件/etc/network/interfaces:sudo vi /etc/network/interfaces在该文件中添加如下的行:auto eth0:1iface eth0:1 inet staticaddress x.x.x.xnetmask x.x.x.xnetwork x.x.x.xbroadcast x.x.x.xgateway x.x.x.x根据你的情况填上所有诸如address,netmask,network,broadcast和gateways等信息:用下面的命令使网络设置生效:sudo /etc/init.d/networking restart4. 设置主机名称(hostname)使用下面的命令来查看当前主机的主机名称:sudo /bin/hostname使用下面的命令来设置当前主机的主机名称:sudo /bin/hostname newname系统启动时,它会从/etc/hostname来读取主机的名称。5. 配置DNS首先,你可以在/etc/hosts中加入一些主机名称和这些主机名称对应的IP地址,这是简单使用本机的静态查询。要访问DNS 服务器来进行查询,需要设置/etc/resolv.conf文件,假设DNS服务器的IP地址是192.168.2.2,那么/etc/resolv.conf文件的内容应为:search chotim.comnameserver 192.168.2.26.手动重启网络服务:sudo /etc/init.d/networking restart返回结果如下:*Reconfiguring network interfaces… [OK]版权声明:本文内容由互联网用户自发贡献,该文观点与技术仅代表作者本人。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌侵权/违法违规的内容, 请发送邮件至 dio@foxmail.com 举报,一经查实,本站将立刻删除。