OpenOCD无法打开与STM32L4开发板的连接STEVAL STWINCSV1

如何解决OpenOCD无法打开与STM32L4开发板的连接STEVAL STWINCSV1

我有一个STEVAL STWINCSV1板，其中STM32L4R9芯片通过USB连接到我的计算机。我正在尝试使用OpenOCD刷新新图像。我正在使用命令openocd -d -f board/stm32l4discovery.cfg尝试打开与主板的连接。这是cfg文件的内容

# Explicitly for the STM32L476 discovery board:
# http://www.st.com/web/en/catalog/tools/PF261635
# but perfectly functional for any other STM32L4 board connected via
# an stlink-v2-1 interface.
# This is for STM32L4 boards that are connected via stlink-v2-1.
 
source [find interface/stlink.cfg]
 
transport select hla_swd
 
source [find target/stm32l4x.cfg]
 
reset_config srst_only

当我通过USB插入开发板并检查dmesg | grep usb的输出时，我得到的是（我多次插入开发板）：

[15316.981696] usb 1-1.3: new full-speed USB device number 7 using xhci_hcd
[15317.119120] usb 1-1.3: New USB device found,idVendor=0483,idProduct=5740,bcdDevice= 2.00
[15317.119121] usb 1-1.3: New USB device strings: Mfr=1,Product=2,SerialNumber=3
[15317.119122] usb 1-1.3: Product: STM32 Virtual ComPort in FS Mode
[15317.119123] usb 1-1.3: Manufacturer: STMicroelectronics
[15317.119123] usb 1-1.3: SerialNumber: FFFFFFFEFFFF
[15317.169176] usbcore: registered new interface driver cdc_acm
[15726.366247] usb 1-1.3: USB disconnect,device number 7
[15733.238286] usb 1-1.3: new full-speed USB device number 8 using xhci_hcd
[15733.363181] usb 1-1.3: New USB device found,bcdDevice= 2.00
[15733.363182] usb 1-1.3: New USB device strings: Mfr=1,SerialNumber=3
[15733.363183] usb 1-1.3: Product: STM32 Virtual ComPort in FS Mode
[15733.363184] usb 1-1.3: Manufacturer: STMicroelectronics
[15733.363184] usb 1-1.3: SerialNumber: FFFFFFFEFFFF
[15822.875489] usb 1-1.3: USB disconnect,device number 8
[15861.278256] usb 1-3.4: new full-speed USB device number 9 using xhci_hcd
[15861.400511] usb 1-3.4: New USB device found,bcdDevice= 2.00
[15861.400512] usb 1-3.4: New USB device strings: Mfr=1,SerialNumber=3
[15861.400513] usb 1-3.4: Product: STM32 Virtual ComPort in FS Mode
[15861.400514] usb 1-3.4: Manufacturer: STMicroelectronics
[15861.400514] usb 1-3.4: SerialNumber: FFFFFFFEFFFF
[16196.113834] usb 1-3.4: USB disconnect,device number 9
[16251.868195] usb 1-1.3: new full-speed USB device number 10 using xhci_hcd
[16252.006377] usb 1-1.3: New USB device found,bcdDevice= 2.00
[16252.006378] usb 1-1.3: New USB device strings: Mfr=1,SerialNumber=3
[16252.006379] usb 1-1.3: Product: STM32 Virtual ComPort in FS Mode
[16252.006380] usb 1-1.3: Manufacturer: STMicroelectronics
[16252.006380] usb 1-1.3: SerialNumber: FFFFFFFEFFFF

当我运行openocd -d -f board/stm32l4discovery.cfg时，输出如下（因为它有点长，所以进行了粘贴）：https://pastebin.com/biVLuf7U

有人知道这里可能出什么问题吗？

解决方法

我发现了问题。首先，我使用的评估板不支持通过usb端口进行stlink，因此我不得不使用stlink / v3 mini外部编程器。另外，我发行版中最新的OpenOCD版本不支持stlink / v3，因此我必须从源代码编译OpenOCD。这解决了我的问题。